UniTak3D

UniTak3D parts and supplies, each one on the bench

• 

  UniTak3D FEP film 140 × 200 mm, 2 sheets

  Two FEP sheets from UniTak3D, 140 × 200 mm and 0.15 mm thick, for 5.5-inch resin printers such as the Photon, Photon S, Mars and Mars 2 Pro, stated to transmit over 95 % of light and resist 204 °C.

  Sheet size

  140 × 200 mm, title and fifth bullet

  Thickness

  0.15 mm, fifth bullet; the box in the product photograph reads 0.127 mm

  Material

  FEP, title

  Pre-mounted frames

  Absent from the listing

  Pack count

  2 sheets, title

  Printer fit

  ELEGOO Mars, Anycubic Photon and Photon S, Mars 2 Pro, LD-002R and LD-002H, Wanhao Duplicator 7, Monoprice Mini Deluxe SLA, EPAX X1, QIDI Tech, Longer Orange and other 5.5-inch printers, title and fourth bullet

  Amazon reference

  B0872BNB9Y (same reference on 6 Amazon marketplaces)

  EAN

  0605175677165

  • Sheet size and thickness published
  • A long list of named 5.5-inch printers
  • Only two sheets, with 0.15 mm in the text and 0.127 mm on the photographed box

  Best for: Replacing the film on an older 5.5-inch resin printer from the named list.

  ≈ 10 €

  Check price on Amazon
• 

  UniTak3D Double-sided PEI plate 235 × 235 mm, smooth and textured

  A double-sided 235 × 235 mm spring steel plate from UniTak3D with textured PEI rated to 300 °C on one side and smooth PEI rated to 200 °C on the other, for Creality printers from the Ender 3 to the K1C.

  Size and fit

  235 × 235 mm with a 220 × 220 mm maximum print area; Creality K1C, K1, Ender 3 V3, V3 SE, V3 KE, CR-10 SE, Ender 3 series, CR 20 and Ender 5 among the printers named, fourth and sixth bullets

  Substrate

  Spring steel sheet, second bullet

  Surface type

  Double-sided: textured black PEI and smooth PEI, real PEI powder coating, title and first three bullets

  Magnetic base

  Absent from the listing

  Filament suitability

  PLA, ABS, ASA, PETG, TPU, nylon, PA and PC; glue stick advised on the smooth side for everything except PLA, third and fifth bullets

  Heat limit

  Textured side to 300 °C, smooth side to 200 °C, third bullet

  Amazon reference

  B08L39BFVJ (same reference on 6 Amazon marketplaces)

  EAN

  0605175679800

  • Separate heat limits for each side: 300 °C textured, 200 °C smooth
  • A long list of Creality printers, including the K1C reviewed on this site
  • No magnetic base mentioned anywhere in the listing

  Best for: A Creality K1C or Ender 3 owner who wants textured PEI for grip and smooth PEI for smooth first layers.

  ≈ £17 / 14 €

  Check price on Amazon
• 

  UniTak3D Blackout cover for small resin printers, 25.5 × 24.5 × 39 cm

  A fabric blackout cover for small resin printers, 25.5 × 24.5 × 39 cm, that keeps dust and direct sunlight off the resin, with flaps on all four sides for reaching controls and ports.

  Inner dimensions

  25.5 × 24.5 × 39 cm, fourth bullet; not stated as inner or outer

  Materials

  Described as waterproof, dustproof and resistant to tearing and abrasion, third bullet; the material is not named

  Ventilation and filtration

  Absent from the listing

  Doors

  Flaps on all four sides for access to the printer’s controls and ports, fifth bullet

  Cable ports

  Absent from the listing as ports — the flaps give access to connections

  Published fire rating

  Absent from the listing

  Amazon reference

  B097D4L3G6 (same reference on 6 Amazon marketplaces)

  EAN

  0605175680011

  • Keeps dust and direct sunlight off a resin printer, which the second bullet ties to keeping the resin in good condition
  • Flaps on all four sides to reach controls without lifting the cover
  • A cover, not an enclosure: no ventilation, filtration or temperature control

  Best for: Covering a small resin printer between prints in a room with daylight.

  ≈ 7 €

  Check price on Amazon