A bench fume extractor sold for soldering and 5 W laser engravers, moving 200 m³/h through a pre-filter, H13 HEPA and activated carbon, each replaceable separately, with an alarm that warns when a filter clogs.
The bottom line A well-described bench extractor: airflow, three replaceable stages, noise and a clog alarm. Its own title sets its scale at 5 W engravers, and it leaves out the hose diameter that decides how it connects.
The FES150S listing, bullet by bullet
Six bullets: soldering and lead fumes drawn through pre-filter cotton, HEPA and activated carbon, each replaceable separately; a 100 W brushless DC motor moving 200 m³/h, H13 HEPA and high-iodine carbon capturing PM0.3 particles at up to 99.97 %; FCC, CE, RoHS and MSDS listed, with use named for soldering, lasers, 3D printing and nail studios; about 50 dB, 24-hour continuous operation and a motor life up to 70,000 hours; pressure monitoring with an audible clog alarm; and a fuse box beside the power switch with two 3 A fuses.
Airflow sized by KNOKOO’s own title
200 m³/h, named for 5 W laser engravers. The maker sets the scale itself. A larger diode or a CO2 cabinet produces more smoke over a larger area, and the listing gives nothing to judge the extractor against those.
What 99.97 % leaves unsaid
The figure is attached to PM0.3 particles and the H13 HEPA stage. The conditions behind it are not described, and the page does not rate how well the unit protects anyone breathing near a job; that is read in the maker’s documentation.
Filters as a running cost
Three stages replaceable separately and an alarm that says when: that is a practical design. Their prices are not on the page, and they are the cost that continues after purchase.
Availability
At the last look-up, the German, French, Italian and Spanish Amazon stores were asking 199 € to 258 €.
It is sold in the American and British Amazon stores as well, in their own currency, which the euro figures above leave out on purpose.
Every figure here is Keepa’s reading on the date this page was last updated. Stock and prices can change at any time.
Prices quoted in this text were read on 15 September 2026. The live price is at the top of the page.
Where it earns its place, and where it falls short
Strengths
Three filter stages that can each be replaced on their own, as the first bullet states
A pressure-based alarm that sounds when a filter clogs
A published noise level, about 50 dB, and continuous 24-hour operation stated
Compromises
Sized in the title for 5 W laser engravers, well below the larger machines in this catalogue
No hose diameter, pressure figure or filter prices
99.97 % is stated without the conditions under which it was reached
Specifications
Airflow
200 m³/h, title and second bullet
Pressure
Absent from the listing — internal air pressure is monitored for filter life, and no figure is given
Filter stages
Three: pre-filter cotton, H13 HEPA and activated carbon, each replaceable separately, first and second bullets
Replacement cost
Absent from the listing
Hose diameter
Absent from the listing
Noise
About 50 dB, fourth bullet
Named materials
Soldering fumes and lead fumes, with use named for soldering, lasers, 3D printing and nail studios; the title names 5 W laser engravers
Amazon reference
B0923MXXTS (same reference on 6 Amazon marketplaces)
EAN
0608410795693
Questions makers ask before buying
Which lasers is it sized for?
The title names 5 W laser engravers and bench soldering. The listing gives no figure for larger machines.
How do I know when to change the filters?
The fifth bullet describes a system that tracks internal air pressure and sounds an alarm when a filter clogs; the maker asks for the blocked filter to be replaced promptly.
115 m³/h · two-layer filter · 63 and 76 mm exhaust ports · 3 speeds · 68 dB, stated both as under and as from · 18.5 × 18.5 × 20.5 cm · 100–240 V
A compact fume filter designed for Creality’s enclosed Falcon A1 engraver, moving 115 m³/h through a two-layer filter, with a port for 63 and 76 mm hoses and a noise figure its title and bullets state two different ways.
Best for: An owner of the enclosed Falcon A1 who wants a matched filter unit rather than a duct to a window.
Low-temperature PCL, 1.75 mm · 2 speeds and 2 temperature levels · cordless, USB-C charging · TouchSafe design · 37 m of PCL in 12 colours included
A cordless 3D pen for children that draws with low-temperature PCL filament, with two speeds and two temperature levels, and a maker’s note that it is used according to the instructions and under supervision.
Best for: A younger child’s first 3D pen, used with an adult nearby, where a low-temperature filament is the point.
Cool-touch design, no external hot parts · one button · reverse function · cordless, USB-C charging · 72 filament strands · ages 6 to 13
A cordless 3D pen for children aged 6 to 13 with a cool-touch design and no external hot parts, sold with 72 filament strands and a guide of ten projects, whose listing names neither the filament material nor a temperature.
Best for: A child from six making simple projects from a guided activity book, with refills bought from the same maker.
