Skip to content

Brand

QWORK

A V5 hotend and long cutting mats

The QWORK hotend

A plug-in V5 J-head for the i3 Mega series, 12 V 40 W, with a 250 °C figure for the heater block.

QWORK cutting mats

Three long mats in light, standard and strong grip, each grip matched to materials, with no grid or care advice.

QWORK parts and supplies, each one on the bench

  • Three long gridded mats in green, blue and purple, the purple one printed with a grip colour key

    QWORK Cutting mats 30.5 × 61 cm, light, standard and strong grip, for Cricut Maker and Explore Air 2, 3 pack

    Three 30.5 × 61 cm cutting mats from QWORK in light, standard and strong grip, for Cricut Maker, Explore Air 2, Air and One cutting machines, with light grip for paper, standard for card and vinyl, and strong for thick card and bonded fabric.

    Size and machine fit
    30.5 × 61 cm, for Cricut Maker, Explore Air 2, Air and One cutting machines, title and first and second bullets
    Grip level
    Light grip, standard grip and strong grip, first bullet
    Material suitability
    Light grip: paper, board and light materials; standard: card, vinyl and medium materials; strong: thick card and reinforced fabric, third to fifth bullets
    Grid markings
    Absent from the listing text — the product photograph shows grids and a colour key: blue light, green standard, pink fabric, purple strong
    Pack contents
    3 mats, title and first bullet
    Film
    Absent from the listing
    Care advice
    Absent from the listing
    Amazon reference
    B0F6XG7S7K (same reference on 6 Amazon marketplaces)
    EAN
    0795973945013
    • The long 30.5 × 61 cm format
    • Each grip matched to materials
    • No grid, film or care advice

    Best for: A Cricut Maker or Explore Air 2 cutting machine owner cutting long banners or borders.

    ≈ 16 €
    Check price on Amazon
  • QWORK hotend with a finned silver heatsink, brass nozzle, two plugged wires and a long white PTFE tube

    QWORK V5 J-head hotend for i3 Mega series 3D printers, 12 V 40 W

    A V5 J-head replacement hotend from QWORK for i3 Mega series 3D printers only, with an aluminium heater block stated to reach 250 °C, a 12 V 40 W heater, a 0.4 mm nozzle and a thermistor and heater cartridge fitted with plugs.

    Printer fit
    Only i3 Mega series 3D printers, title and second bullet
    Maximum temperature
    The aluminium heater block can reach 250 °C, first bullet
    Heat break
    V5 heater tube, fourth bullet; no material given
    Nozzle standard
    V5 J-head, 0.4 mm nozzle for 1.75 mm filament, title and fourth bullet
    Heater and thermistor
    12 V 40 W heater; thermistor and heater cartridge both supplied with plugs, fourth and fifth bullets
    Cooling
    Absent from the listing text — the product photograph shows a finned silver heatsink
    Melt zone
    Absent from the listing — a 45° chamfer at the rear and a flat, smooth nozzle section are described, third bullet
    Amazon reference
    B0B1WWMMYS (same reference on 5 Amazon marketplaces)
    EAN
    0795973834089
    • Thermistor and heater cartridge arrive with plugs, as the fifth bullet says
    • A temperature figure for the heater block: 250 °C
    • Only for the i3 Mega series

    Best for: An i3 Mega series owner replacing a worn V5 hotend with a plug-in part.

    ≈ 8 €
    Check price on Amazon

A price quoted in the text of a MakerVerdict page dates from the day that page was written; the live figure beside each product is fetched while you read and replaces it.