Skip to content

Brand

SCULPFUN

An air assist nozzle and a rotary roller

SCULPFUN air assist

A nozzle kit for S9 and S6 Pro modules from October 2021 onward, without a pump.

SCULPFUN rotary

A pre-assembled roller with 70A rubber shafts and a 5–150 mm range, plugged into an X or Y stepper, with no tilt.

SCULPFUN parts and supplies, each one on the bench

  • Black SCULPFUN roller frame turning a blue can, beside engraved bottles, cups and glasses

    SCULPFUN Rotary roller with 70A rubber shafts, 5–150 mm, four metal riser feet

    A pre-assembled rotary roller from SCULPFUN with two high-friction 70A rubber shafts, sliding shaft spacing locked by a knob, four metal riser feet, a 5–150 mm engraving range, an adapter cable for the engraver’s X or Y stepper wiring, and a tape measure for diameters.

    Roller or chuck design
    Two 70A rubber rollers; spacing set by sliding and locked with a hand knob, first and fourth bullets
    Diameter range
    5–150 mm engraving range, second bullet
    Maximum length
    Absent from the listing
    Height
    Absent from the listing as a figure — four metal riser feet and a separate stand for different machines, first and second bullets
    Connector
    Adapter cable to the engraver’s X-axis or Y-axis stepper motor wiring, third bullet
    Software support
    LightBurn and LaserGRBL, with no parameter setting needed, fifth bullet
    Tilt adjustment
    Absent from the listing
    Amazon reference
    B09Q932PVD (same reference on 5 Amazon marketplaces)
    EAN
    0860013771119
    • Pre-assembled, with an adapter cable for X or Y stepper wiring
    • Sliding roller spacing locked by hand
    • No tilt adjustment

    Best for: An open-frame diode engraver owner engraving pens, bottles and tumblers with parallel sides.

    ≈ £110 / 99 €
    Check price on Amazon
  • SCULPFUN nozzle with brass elbow, red acrylic shield, blue air tube, three green O-rings, screws, hex keys and a black band

    SCULPFUN S9 air assist nozzle kit with tube and sealing ring, pump not included

    An official all-metal air assist nozzle from SCULPFUN for S9 and S6 Pro laser modules with the conical shroud, made after October 2021, supplied with an air tube, sealing ring and fittings but no air pump.

    Airflow
    Absent from the listing
    Pressure
    Absent from the listing
    Nozzle fit
    SCULPFUN S9 and S6 Pro modules with the conical shroud, from October 2021; earlier machines not suitable, first and second bullets
    Flow control
    Absent from the listing
    Noise
    Absent from the listing
    Tubing
    Air tube, sealing ring and installation parts included, fifth bullet; the product photograph shows a blue tube, three green O-rings, a red acrylic shield, four screws and two hex keys
    Power supply
    Absent from the listing — no pump included, third and fifth bullets
    Amazon reference
    B0B69D875D (same reference on 6 Amazon marketplaces)
    EAN
    9039089732817
    • A plain cut-off: S9 and S6 Pro modules from October 2021
    • A sealing ring that keeps pump air in and dust off the lens
    • Air pump not included

    Best for: A SCULPFUN S9 or S6 Pro owner with a post-October 2021 module and an air pump already on the bench.

    ≈ $40 / £36 / 35 €
    Check price on Amazon

A price quoted in the text of a MakerVerdict page dates from the day that page was written; the live figure beside each product is fetched while you read and replaces it.