Hot or cold nozzle, and which filament it takes, before any colour count · review
MYNT3D Super 3D Pen for ABS and PLA review
A slim 1.75 mm pen for ABS and PLA with a stepless speed slider and an ultrasonically sealed nozzle, described in five short bullets that give no temperature and no safety provision.
The bottom line The shortest of the four pen listings reviewed here, and the most open on filament: standard 1.75 mm ABS and PLA with a speed slider. It is also the least forthcoming on heat and safety, which sits badly beside a claim that it suits children.
The Super 3D Pen listing, bullet by bullet
Five short bullets: turning ordinary drawings into 3D artworks; a stepless speed slider for controlling material flow while drawing; an ultrasonically sealed nozzle, new for 2019, described as nearly clog-proof; a pen ideal for children, artists and engineers of all ages; and a kit with three colours of PLA, an AC adapter and a slim, ergonomic pen.
Standard filament
1.75 mm ABS and PLA is the most practical line on the page. Refills are easy to find, and colours are not limited to one maker’s range.
Where the MYNT3D listing goes quiet
No temperature is given for a pen melting ABS and PLA, and no safety provision is described. The fourth bullet nonetheless calls it ideal for children. This page reports the claim and leaves the instructions and supervision to decide.
A dated description
The third bullet calls the nozzle new for 2019. That is the only date on the page, and it tells a buyer the description has not been updated recently rather than anything about the product in the box.
Availability
At the last look-up, the German, French and Italian Amazon stores were asking 36 € to 50 €.
It is sold in the American and British Amazon stores as well, in their own currency, which the euro figures above leave out on purpose.
The asking price on the Spanish Amazon store ran past 1.6× the lowest country’s. A gap that size points to goods shipped in from abroad rather than a local seller, so that offer is left out of the figures above.
Every figure here is Keepa’s reading on the date this page was last updated. Stock and prices can change at any time.
Prices quoted in this text were read on 15 September 2026. The live price is at the top of the page.
Where it earns its place, and where it falls short
Strengths
Accepts standard 1.75 mm ABS and PLA, the most widely available pen filaments
A stepless slider for fine control of material flow while drawing
A nozzle the maker describes as ultrasonically sealed against clogging
Compromises
No temperature figure for a pen that melts ABS and PLA
No safety provision described, although the listing calls it ideal for children
Very short bullets, one of which dates the nozzle design to 2019
Specifications
Nozzle type
Ultrasonically sealed nozzle, described as nearly clog-proof, third bullet
Temperature
Absent from the listing
Filament accepted
1.75 mm ABS and PLA, title
Speed control
Stepless speed slider, second bullet
Power source
AC adapter, fifth bullet
Weight
Absent from the listing — described as slim and ergonomic
Published safety features
Absent from the listing
Amazon reference
B081C946ZJ (same reference on 6 Amazon marketplaces)
EAN
0850751007076
Questions makers ask before buying
Does it take standard filament?
Yes, according to the title: 1.75 mm ABS and PLA. The kit includes three colours of PLA.
Is it suitable for children?
The fourth bullet describes it as ideal for children, artists and engineers of all ages. The listing publishes no temperature and no safety feature, so the maker’s instructions and adult supervision are the reference.
Low-temperature PCL, 1.75 mm · 2 speeds and 2 temperature levels · cordless, USB-C charging · TouchSafe design · 37 m of PCL in 12 colours included
A cordless 3D pen for children that draws with low-temperature PCL filament, with two speeds and two temperature levels, and a maker’s note that it is used according to the instructions and under supervision.
Best for: A younger child’s first 3D pen, used with an adult nearby, where a low-temperature filament is the point.
Cool-touch design, no external hot parts · one button · reverse function · cordless, USB-C charging · 72 filament strands · ages 6 to 13
A cordless 3D pen for children aged 6 to 13 with a cool-touch design and no external hot parts, sold with 72 filament strands and a guide of ten projects, whose listing names neither the filament material nor a temperature.
Best for: A child from six making simple projects from a guided activity book, with refills bought from the same maker.
Ceramic tip · adjustable temperature, PLA 160–210 °C and ABS 210–235 °C · stepless speed · 2–3 min heat-up · auto standby after 2 min · mains adapter
A mains-powered 3D pen with a display, a ceramic tip and adjustable temperature, whose listing publishes the ranges for PLA and ABS and an automatic standby after two minutes idle.
Best for: An older child or adult who wants to draw with PLA and ABS at published temperatures, including small repairs.
