Skip to content

The one that prints its settings on the listing

SUNLU PETG 1.75 mm, black, 1 kg, with print settings

A 1 kg spool of black SUNLU PETG in 1.75 mm with a ±0.02 mm tolerance, whose listing recommends a 220–230 °C nozzle, a 60–70 °C bed and speeds from 40 to 600 mm/s, in airtight vacuum packaging.

SUNLU black PETG filament spool

SUNLU PETG 1.75 mm, black, 1 kg, with print settings

A 1 kg spool of black SUNLU PETG in 1.75 mm with a ±0.02 mm tolerance, whose listing recommends a 220–230 °C nozzle, a 60–70 °C bed and speeds from 40 to 600 mm/s, in airtight vacuum packaging.

Diameter tolerance
±0.02 mm, eighth bullet
Net weight
1 kg, title
Recommended temperatures
Nozzle 220–230 °C, bed 60–70 °C, print speed 40–600 mm/s, seventh bullet
Adhesion guidance
Absent from the listing as guidance — excellent layer adhesion is claimed, second bullet
Moisture packaging
Airtight vacuum packaging, ninth bullet
Transparency
Absent from the listing
Spool size
Absent from the listing
Amazon reference
B07TJDTJZD (same reference on 5 Amazon marketplaces)
EAN
0768894219198
  • Recommended nozzle, bed and speed settings published
  • A ±0.02 mm tolerance
  • No desiccant mentioned

Best for: A first PETG spool, printed from the settings on the listing.

≈ £13 / 14 €
Check price on Amazon

Specifications

Diameter tolerance
±0.02 mm, eighth bullet
Net weight
1 kg, title
Recommended temperatures
Nozzle 220–230 °C, bed 60–70 °C, print speed 40–600 mm/s, seventh bullet
Adhesion guidance
Absent from the listing as guidance — excellent layer adhesion is claimed, second bullet
Moisture packaging
Airtight vacuum packaging, ninth bullet
Transparency
Absent from the listing
Spool size
Absent from the listing
Amazon reference
B07TJDTJZD (same reference on 5 Amazon marketplaces)
EAN
0768894219198

The SUNLU PETG listing, bullet by bullet

Ten bullets: a 1.75 mm PETG combining properties of PLA and ABS; excellent layer adhesion; toughness; impact resistance; durability for indoor and outdoor use; less stringing and no clogging; recommended settings of 220–230 °C nozzle, 60–70 °C bed and 40–600 mm/s; a ±0.02 mm tolerance; airtight vacuum packaging; and a list of SUNLU products.

Settings on the SUNLU listing

Nozzle, bed and speed ranges in one bullet. The seventh bullet gives what a first print needs. None of the three other PETGs here publishes a temperature.

A speed range with a wide top

40 to 600 mm/s spans slow, careful printers and high-speed machines. The upper figure is what the material is said to tolerate, not a speed every print will run at.

Packaging without desiccant

The ninth bullet describes airtight vacuum packaging and mentions no desiccant, which the Kingroon and eSUN spools include.

Availability

At the last look-up, the German, French, Italian and Spanish Amazon stores were asking 14 € to 20 €.

It is sold in the British Amazon store as well, in its own currency, which the euro figures above leave out on purpose.

The American Amazon store returned no entry, so the buy button there opens a search rather than a missing page.

Every figure here is Keepa’s reading on the date this page was last updated. Stock and prices can change at any time.

Prices quoted in this text were read on 15 September 2026. The live price is at the top of the page.

More PETG filament

  • 3DHoJor white PETG filament spool

    3DHoJor PETG 1.75 mm, white, 1 kg, dried and vacuum-sealed

    A 1 kg spool of white 3DHoJor PETG in 1.75 mm, dried for 24 hours and vacuum-sealed with desiccant, described as tough, moisture-resistant and glossy, with no tolerance or print settings published.

    Diameter tolerance
    Absent from the listing — 1.75 mm in the title
    Net weight
    1 kg, title
    Recommended temperatures
    Absent from the listing
    Adhesion guidance
    Absent from the listing — printing without warping or shrinking is claimed, second bullet
    Moisture packaging
    Dried for 24 hours, then vacuum-sealed with a desiccant bag, fifth bullet
    Transparency
    Described as glossy with high clarity and light transmission, fourth bullet
    Spool size
    Absent from the listing
    Amazon reference
    B0F18YP1CJ (same reference on 6 Amazon marketplaces)
    EAN
    0614141603473
    • Dried for 24 hours before vacuum sealing with desiccant
    • The cheapest PETG of the four here
    • No diameter tolerance

    Best for: Everyday PETG parts for someone who will set temperatures from their own printer profile.

    ≈ $12 / £11 / 9 €
    Check price on Amazon
  • eSUN PETG Basic black filament spool

    eSUN PETG Basic 1.75 mm, black, 1 kg

    A 1 kg spool of black eSUN PETG Basic in 1.75 mm, described as tough, glossy, weather- and chemical-resistant with good winding, sealed in a vacuum bag with desiccant, and published without a tolerance figure or print settings.

    Diameter tolerance
    Absent from the listing as a figure — “minimal tolerance” and tight diameter tolerance are described, third and fourth bullets
    Net weight
    1 kg, title
    Recommended temperatures
    Absent from the listing
    Adhesion guidance
    Absent from the listing — good layer bonding is claimed, third bullet
    Moisture packaging
    Vacuum-sealed bag with desiccant, fifth bullet
    Transparency
    Described as having excellent clarity, light transmission and high gloss, first bullet
    Spool size
    Absent from the listing
    Amazon reference
    B0DDTFL214 (same reference on 5 Amazon marketplaces)
    EAN
    6922572209060
    • Weather and chemical resistance named, with toughness close to ABS as described
    • Good winding without overlaps, as the fourth bullet states
    • Tolerance described but not given as a figure

    Best for: General PETG parts such as containers and accessories, printed from a known profile.

    ≈ 12 €
    Check price on Amazon
  • Kingroon black PETG filament spool

    Kingroon PETG 1.75 mm ±0.02 mm, black, 1 kg

    A 1 kg spool of black Kingroon PETG in 1.75 mm with a ±0.02 mm tolerance, whose listing states heat resistance up to 84 °C and flexural strength up to 69.6 MPa, vacuum-sealed with desiccant.

    Diameter tolerance
    ±0.02 mm, title and fourth bullet
    Net weight
    1 kg, title
    Recommended temperatures
    Absent from the listing — heat resistance of up to 84 °C is stated for printed parts, second bullet
    Adhesion guidance
    Absent from the listing — strong layer adhesion is claimed, fifth bullet
    Moisture packaging
    Vacuum-sealed with desiccant, fifth bullet
    Transparency
    Absent from the listing
    Spool size
    Absent from the listing
    Amazon reference
    B0C6G8MDZX (same reference on 5 Amazon marketplaces)
    EAN
    0749684714185
    • Material figures published: heat resistance to 84 °C, flexural strength to 69.6 MPa
    • A ±0.02 mm tolerance and tangle-free winding
    • No print temperatures or bed guidance

    Best for: Functional brackets, tool holders and enclosures where a published heat and strength figure helps choose a material.

    ≈ 10 €
    Check price on Amazon

Elsewhere on the workbench

  • GEEETECH black PLA filament spool beside a black printed figure

    GEEETECH PLA 1.75 mm, black, 1 kg spool

    A spool of black GEEETECH PLA in 1.75 mm with a ±0.02 mm tolerance and a printing range of 190–220 °C, vacuum-packed, whose weight is given as 1 kg in the title and 1.1 kg in the first bullet.

    Diameter and tolerance
    1.75 mm ±0.02 mm, first and fourth bullets
    Net weight
    1 kg in the title; 1.1 kg spool in the first bullet
    Spool size
    Absent from the listing
    Recommended temperatures
    Printing temperature 190–220 °C, third bullet; no bed temperature
    Finish
    Absent from the listing — black, title
    Winding
    Absent from the listing
    Packaging
    Vacuum packaging, first bullet
    Amazon reference
    B071DM81ZK (same reference on 5 Amazon marketplaces)
    EAN
    0718399619665
    • A published printing temperature range, 190–220 °C
    • Vacuum packaging and a ±0.02 mm tolerance
    • Weight given as 1 kg in the title and 1.1 kg in the bullets

    Best for: A PLA user who wants a stated temperature range to start tuning from.

    ≈ 12 €
    Check price on Amazon
  • SUNLU PLA+ white filament spool

    SUNLU PLA+ 1.75 mm, white, 1 kg

    A 1 kg spool of white SUNLU PLA+ in 1.75 mm with a ±0.02 mm tolerance, on a spool whose diameter, width and hole size are all published, wound by machine and inspected by hand.

    Diameter and tolerance
    1.75 mm ±0.02 mm, third bullet
    Net weight
    1 kg, title
    Spool size
    Diameter 20.32 cm, width 6.35 cm, hole 5.59 cm, fourth bullet
    Recommended temperatures
    Absent from the listing
    Finish
    PLA+, white; described as stronger than normal PLA with brighter colours, first bullet
    Winding
    Fully mechanical winding with manual inspection, no overlaps, second and third bullets
    Packaging
    Absent from the listing
    Amazon reference
    B07XFL3XB9 (same reference on 5 Amazon marketplaces)
    EAN
    0747045295922
    • Spool diameter, width and hole size published, so holder fit can be checked
    • A ±0.02 mm diameter tolerance
    • No recommended print temperatures

    Best for: Everyday PLA printing on an FDM printer whose spool holder needs checked dimensions.

    ≈ 11 €
    Check price on Amazon
  • Five AIRCUT gridded mats fanned out in purple, blue, pink and two greens, labels reading StrongGrip, LightGrip and FabricGrip

    AIRCUT Cutting mats 12 × 12 in, light, standard, strong and fabric grip, for Cricut cutting plotters, 5 pack

    Five 12 × 12 in PVC cutting mats from AIRCUT in four grip levels — light, standard, strong and fabric — for Cricut Explore 5, One, Air, Air 2, 3 and 4 and Maker, Maker 3 and Maker 4 cutting machines, with a clear film to keep on in storage.

    Size and machine fit
    12 × 12 in, for Cricut Explore 5, One, Air, Air 2, 3, 4, Maker, Maker 3 and Maker 4 cutting machines, first bullet
    Grip level
    Light, standard, strong and fabric grip across 5 mats, first bullet; split not given
    Material suitability
    Card, construction paper, printable fabric and iron-on, pearl paper, printer paper, parchment, vinyl, washi sheets, window film, fourth bullet
    Grid markings
    Absent from the listing text — the product photograph shows inch grids
    Pack contents
    5 mats of 12 × 12 in, first bullet; in the product photograph the front green mat is labelled StrongGrip and no StandardGrip label is legible
    Film
    Clear film, fifth bullet
    Care advice
    Keep the clear film on in storage to keep off paper scraps and dust, fifth bullet
    Amazon reference
    B0C6JTP73L (same reference on 6 Amazon marketplaces)
    EAN
    0762102992545
    • Four grip levels including fabric grip
    • Five mats
    • Which grip comes twice is not said

    Best for: A Cricut Maker cutting machine owner who cuts fabric as well as paper and vinyl.

    ≈ $14 / £13 / 17 €
    Check price on Amazon

All PETG filament