Skip to content

From the bench supply to the board

Cleqee Stackable banana plug to breadboard male jumper leads, 10 pieces, silicone

Ten test leads from Cleqee with soft silicone insulation, about 27.2 cm long, each with a stackable banana plug at one end and a male breadboard jumper pin at the other, in five colours, for connecting power supplies, multimeters and LED strips to a breadboard.

Ten silicone leads in red, black, yellow, green and blue pairs, stackable banana plugs at one end and pins at the other

Cleqee Stackable banana plug to breadboard male jumper leads, 10 pieces, silicone

Ten test leads from Cleqee with soft silicone insulation, about 27.2 cm long, each with a stackable banana plug at one end and a male breadboard jumper pin at the other, in five colours, for connecting power supplies, multimeters and LED strips to a breadboard.

Tie points
Absent from the listing — leads only
Power rails
Absent from the listing
Contact quality
Stackable banana plugs; pure copper male breadboard pins, second and third bullets
Backing
Absent from the listing
Wire types and lengths
Banana plug to male breadboard pin, about 27.2 cm, silicone insulation, first, third and fifth bullets
Gauge
Absent from the listing
Pack contents
10 leads in 5 colours, fifth bullet
Amazon reference
B08Q7PXVL9 (same reference on 5 Amazon marketplaces)
EAN
0784110446100
  • Stackable banana plugs
  • Soft silicone insulation
  • No gauge or current rating

Best for: A maker powering a breadboard from a bench power supply or probing it with a multimeter.

≈ £9 / 10 €
Check price on Amazon

Specifications

Tie points
Absent from the listing — leads only
Power rails
Absent from the listing
Contact quality
Stackable banana plugs; pure copper male breadboard pins, second and third bullets
Backing
Absent from the listing
Wire types and lengths
Banana plug to male breadboard pin, about 27.2 cm, silicone insulation, first, third and fifth bullets
Gauge
Absent from the listing
Pack contents
10 leads in 5 colours, fifth bullet
Amazon reference
B08Q7PXVL9 (same reference on 5 Amazon marketplaces)
EAN
0784110446100

The Cleqee lead listing, bullet by bullet

Five bullets: silicone leads that stay soft and handle heat and cold; stackable banana plugs, more than one in a socket; male breadboard pins in insulated pure copper for power supplies, LED strips, multimeters and Lilypad; use in electrical work with Arduino and Raspberry Pi microcontroller boards and single-board computers such as Orange Pi; and ten leads of about 27.2 cm in five colours.

Banana at one end, pin at the other. Bench power supplies and multimeters use banana sockets; breadboards use pins. These leads join the two without clips.

What Cleqee leaves out

No wire gauge and no current rating. For a power supply lead, those decide how much current is sensible to run through it.

Availability

At the last look-up, the German, French, Italian and Spanish Amazon stores were asking 10 € to 14 €.

It is sold in the British Amazon store as well, in its own currency, which the euro figures above leave out on purpose.

The American Amazon store returned no entry, so the buy button there opens a search rather than a missing page.

Every figure here is Keepa’s reading on the date this page was last updated. Stock and prices can change at any time.

Prices quoted in this text were read on 15 September 2026. The live price is at the top of the page.

More breadboards and jumper wires

  • Long white solderless breadboard with red and blue rail lines along both edges, beside a bundle of flexible jumper wires

    CyConncet Solderless breadboard 5.4 × 16.5 cm with two distribution strips

    A solderless breadboard from CyConncet, 5.4 × 16.5 × 0.85 cm in ABS, with nickel-plated phosphor bronze spring clips, two distribution strips, top and bottom rows connected horizontally and the rest vertically, for 0.8 mm jumper wires, and joinable with other units.

    Tie points
    Two distribution strips, 200 jacks, first bullet
    Power rails
    Top and bottom rows connected horizontally and split in the middle, fourth bullet
    Contact quality
    Nickel-plated phosphor bronze spring clips, first bullet
    Backing
    Absent from the listing — ABS plastic, joinable by units, second and fifth bullets
    Wire types and lengths
    Absent from the listing — matching jumper wire diameter 0.8 mm, first and second bullets
    Gauge
    0.8 mm wire diameter, second bullet
    Pack contents
    Absent from the listing text — board size 5.4 × 16.5 × 0.85 cm, first bullet; the product photograph shows the board with a bundle of flexible jumper wires
    Amazon reference
    B0D3BZBHVS (same reference on 6 Amazon marketplaces)
    EAN
    0784633677708
    • Nickel-plated phosphor bronze contacts
    • Board size given: 5.4 × 16.5 × 0.85 cm
    • Rails split in the middle

    Best for: A beginner prototyping small circuits who may join boards together later.

    ≈ 5 €
    Check price on Amazon
  • Three rainbow jumper wire ribbons, one long and two short, with pin and socket ends

    GERUI Jumper wires 120 pieces, M-F, M-M and F-F, 10 and 20 cm, 28 AWG

    Three 40-wire ribbons of jumper wires from GERUI — male to female, male to male and female to female — in 10 and 20 cm lengths, 28 AWG with PVC insulation and 2.54 mm pitch ends, separable into single wires.

    Tie points
    Absent from the listing — wires only
    Power rails
    Absent from the listing
    Contact quality
    Small pins and sockets for 2.54 mm pitch, holding firmly, third and fifth bullets
    Backing
    Absent from the listing
    Wire types and lengths
    40 male-female, 40 male-male and 40 female-female; 10 cm and 20 cm, first and second bullets
    Gauge
    28 AWG, title
    Pack contents
    3 ribbons of 40 wires, 120 in all, title and second bullet
    Amazon reference
    B0DGBYR2YL (same reference on 6 Amazon marketplaces)
    EAN
    0744243857648
    • All three end types
    • Two lengths: 10 and 20 cm
    • “Male to Female” in the title, three types in the box

    Best for: A maker wiring modules to a board or single-board computer GPIO header.

    ≈ 6 €
    Check price on Amazon
  • Three equal-length rainbow jumper ribbons: socket to socket, socket to pin and pin to pin

    ELEGOO Jumper wires 3 × 40, 20 cm, M-M, F-M and F-F

    Three 40-wire ribbons of 20 cm jumper wires from ELEGOO — female to female, male to female and male to male — in many colours for following a circuit, separable into single wires.

    Tie points
    Absent from the listing — wires only
    Power rails
    Absent from the listing
    Contact quality
    Absent from the listing
    Backing
    Absent from the listing
    Wire types and lengths
    40 female-female, 40 male-female, 40 male-male; 20 cm, third and fourth bullets
    Gauge
    Absent from the listing
    Pack contents
    3 ribbons of 40 wires, fourth bullet
    Amazon reference
    B01EV70C78 (same reference on 3 Amazon marketplaces)
    EAN
    0719377200424
    • All three end types
    • Many colours for tracing a circuit
    • One length only: 20 cm

    Best for: A breadboard user who wants one length of each wire type from the same maker as their board.

    ≈ $7 / £6 / 7 €
    Check price on Amazon

Elsewhere on the workbench

  • TIOPY gold textured PEI spring steel plate with a handling tab

    TIOPY PEI spring steel plate 257 × 257 mm for Bambu Lab 3D printers

    A 257 × 257 mm PEI spring steel plate from TIOPY for Bambu Lab X1, P1, P2S and A1 printers, carrying no QR code, so the printer’s plate detection has to be turned off; its PEI is called smooth in the title and textured in the bullets.

    Size and fit
    257 × 257 mm for Bambu Lab X2D, X1, X1C, X1E, P1P, P1S, P2S and A1, title and first bullet
    Substrate
    Spring steel, title and second and fourth bullets
    Surface type
    “Smooth PEI” in the title; double-sided textured PEI in the first, fourth and fifth bullets, frosted PEI surface in the second; the product photograph shows a gold textured face
    Magnetic base
    Absent from the listing
    Filament suitability
    PLA, flexible, wood, ABS, PC, PETG, TPU and nylon, second bullet
    Heat limit
    Can be heated to over 200 °C, second bullet; no upper limit given
    Amazon reference
    B0CBH3B8GT (same reference on 6 Amazon marketplaces)
    EAN
    0738260308610
    • A plain instruction that the plate has no QR code and plate detection must be disabled
    • Named for the Bambu Lab X1, P1, P2S and A1 series
    • Smooth in the title, textured in the bullets

    Best for: A Bambu Lab X1, P1 or A1 owner who wants a spare PEI plate and can do without automatic plate detection.

    ≈ 14 €
    Check price on Amazon
  • UniTak3D PEI plate, black textured face marked PEI Texture and smooth face marked PEI Smooth

    UniTak3D Double-sided PEI plate 235 × 235 mm, smooth and textured

    A double-sided 235 × 235 mm spring steel plate from UniTak3D with textured PEI rated to 300 °C on one side and smooth PEI rated to 200 °C on the other, for Creality printers from the Ender 3 to the K1C.

    Size and fit
    235 × 235 mm with a 220 × 220 mm maximum print area; Creality K1C, K1, Ender 3 V3, V3 SE, V3 KE, CR-10 SE, Ender 3 series, CR 20 and Ender 5 among the printers named, fourth and sixth bullets
    Substrate
    Spring steel sheet, second bullet
    Surface type
    Double-sided: textured black PEI and smooth PEI, real PEI powder coating, title and first three bullets
    Magnetic base
    Absent from the listing
    Filament suitability
    PLA, ABS, ASA, PETG, TPU, nylon, PA and PC; glue stick advised on the smooth side for everything except PLA, third and fifth bullets
    Heat limit
    Textured side to 300 °C, smooth side to 200 °C, third bullet
    Amazon reference
    B08L39BFVJ (same reference on 6 Amazon marketplaces)
    EAN
    0605175679800
    • Separate heat limits for each side: 300 °C textured, 200 °C smooth
    • A long list of Creality printers, including the K1C reviewed on this site
    • No magnetic base mentioned anywhere in the listing

    Best for: A Creality K1C or Ender 3 owner who wants textured PEI for grip and smooth PEI for smooth first layers.

    ≈ £17 / 14 €
    Check price on Amazon
  • YOOPAI green plate printed PLA/PETG and Cool Plate Ultra Tack along its front edge

    YOOPAI Cold plate 257 × 257 mm for Bambu Lab 3D printers, with identification code

    A green 257 × 257 mm cold-print plate for Bambu Lab 3D printers that grips PLA at 45–55 °C and PETG at 50–70 °C, with an identification code for the X1C and X1E, a scraper, and a warning against ABS and TPU.

    Size and fit
    257 × 257 mm for Bambu Lab A1, P2S, X2D, P1P, P1S, X1C and X1E, title and fourth bullet
    Substrate
    Flexible steel plate, third bullet
    Surface type
    Textured cold-print surface, green, title and third bullet; identification code for automatic bed levelling on X1C and X1E, fourth bullet
    Magnetic base
    Absent from the listing
    Filament suitability
    PLA at 45–55 °C and PETG at 50–70 °C; not recommended for ABS or TPU, second bullet
    Heat limit
    Absent from the listing
    Amazon reference
    B0FNMPXGFP (same reference on 6 Amazon marketplaces)
    EAN
    0850078714053
    • Bed temperatures given per material: PLA 45–55 °C, PETG 50–70 °C
    • An identification code for X1C and X1E automatic bed levelling
    • Not recommended for ABS or TPU

    Best for: A Bambu Lab 3D printer owner printing large PLA and PETG parts who wants lower bed temperatures and less warping.

    ≈ $18 / £18 / 15 €
    Check price on Amazon

All breadboards and jumper wires