Skip to content

Brand

eSUN

Properties named, print settings left out

eSUN’s four spools

PLA Basic formulated for high-speed printers, PETG Basic, a carbon-fibre-filled PLA and TPU-95A, all 1.75 mm and 1 kg, the vacuum-sealed ones with desiccant.

What eSUN describes

Material behaviour. The TPU lists resistance to oil, solvents, scratches and weather; the PETG names weather and chemical resistance; the PLA-CF compares its shrinkage and water absorption with eSUN’s own ePA-CF. Two of the four name the AnkerMake M5 reviewed on this site among compatible printers.

What eSUN does not

Print temperatures, on any of the four. The PLA-CF does not say whether a hardened nozzle is needed, and only the PLA gives a tolerance figure.

eSUN parts and supplies, each one on the bench

  • eSUN ePLA-CF carbon fibre filled black filament spool

    eSUN PLA-CF carbon fibre filled 1.75 mm, black, 1 kg

    A 1 kg spool of black eSUN ePLA-CF: PLA with chopped carbon fibre for higher strength and flexural modulus and a matte finish, named as compatible with fast printers including the AnkerMake M5, with no nozzle guidance.

    Base polymer
    PLA, first bullet
    Filler
    Chopped carbon fibre, organically infiltrated, first bullet
    Nozzle requirement
    Absent from the listing
    Recommended temperatures
    Absent from the listing
    Drying advice
    Absent from the listing — lower water absorption than eSUN ePA-CF is stated, fourth bullet
    Net weight
    1 kg, title
    Finish
    Matte carbon fibre texture with less visible layering, second bullet
    Amazon reference
    B0CH36F58Y (same reference on 6 Amazon marketplaces)
    EAN
    0840249104332
    • Carbon fibre filler for higher strength and flexural modulus, as stated
    • A matte finish that makes layer lines less visible
    • No mention of whether a hardened nozzle is needed

    Best for: Stiff jigs, brackets and drone parts on a fast printer, once the nozzle is confirmed suitable.

    ≈ £20 / 17 €
    Check price on Amazon
  • eSUN black TPU-95A filament spool

    eSUN TPU-95A 1.75 mm, black, 1 kg

    A 1 kg spool of black eSUN TPU-95A in 1.75 mm, listing resistance to oil, solvents, scratches, tearing and weather, with good winding, in a vacuum-sealed bag with desiccant and no print settings.

    Shore hardness
    95A, title and first bullet
    Diameter tolerance
    Absent from the listing as a figure — very tight tolerance described, third bullet
    Net weight
    1 kg net, title and fifth bullet
    Recommended speed and temperatures
    Absent from the listing
    Extruder guidance
    Absent from the listing
    Packaging
    Vacuum-sealed bag with desiccant, fifth bullet
    Amazon reference
    B07PM2R9ZM (same reference on 6 Amazon marketplaces)
    EAN
    0781520911426
    • Resistance to oil, solvents, scratches, tearing, flexing and weather named
    • Net filament weight stated as 1 kg
    • No tolerance figure

    Best for: Flexible parts exposed to oil or outdoor conditions, such as gaskets, bumpers and straps.

    ≈ $28 / £19 / 18 €
    Check price on Amazon
  • eSUN PETG Basic black filament spool

    eSUN PETG Basic 1.75 mm, black, 1 kg

    A 1 kg spool of black eSUN PETG Basic in 1.75 mm, described as tough, glossy, weather- and chemical-resistant with good winding, sealed in a vacuum bag with desiccant, and published without a tolerance figure or print settings.

    Diameter tolerance
    Absent from the listing as a figure — “minimal tolerance” and tight diameter tolerance are described, third and fourth bullets
    Net weight
    1 kg, title
    Recommended temperatures
    Absent from the listing
    Adhesion guidance
    Absent from the listing — good layer bonding is claimed, third bullet
    Moisture packaging
    Vacuum-sealed bag with desiccant, fifth bullet
    Transparency
    Described as having excellent clarity, light transmission and high gloss, first bullet
    Spool size
    Absent from the listing
    Amazon reference
    B0DDTFL214 (same reference on 5 Amazon marketplaces)
    EAN
    6922572209060
    • Weather and chemical resistance named, with toughness close to ABS as described
    • Good winding without overlaps, as the fourth bullet states
    • Tolerance described but not given as a figure

    Best for: General PETG parts such as containers and accessories, printed from a known profile.

    ≈ 12 €
    Check price on Amazon
  • eSUN PLA Basic white filament spool

    eSUN PLA Basic 1.75 mm for fast printers, white, 1 kg

    A 1 kg spool of white eSUN PLA Basic in 1.75 mm with a ±0.03 mm tolerance, formulated for high-speed printing and named as compatible with printers including the AnkerMake M5, sealed in a vacuum bag with desiccant.

    Diameter and tolerance
    1.75 mm ±0.03 mm, title
    Net weight
    1 kg, title
    Spool size
    Absent from the listing
    Recommended temperatures
    Absent from the listing
    Finish
    Absent from the listing — white, title
    Winding
    Absent from the listing
    Packaging
    Vacuum-sealed bag with desiccant, fifth bullet
    Amazon reference
    B0CR1CS3K8 (same reference on 5 Amazon marketplaces)
    EAN
    6922572205635
    • Formulated for high-speed printing, with compatible printers named
    • Vacuum-sealed with a desiccant bag
    • A ±0.03 mm tolerance, looser than the ±0.02 mm of four other PLAs here

    Best for: Fast CoreXY and high-speed bed-slinger printers, including the AnkerMake M5 reviewed on this site.

    ≈ £12 / 13 €
    Check price on Amazon

A price quoted in the text of a MakerVerdict page dates from the day that page was written; the live figure beside each product is fetched while you read and replaces it.